金屬屏蔽電力電纜Metal Shielding Power Cable

一、適用范圍

本產品適用于額定電壓0.6/1KV及以下的電力線路中作輸送電能用。產品具有較強的電磁干擾、抗雷擊及均衡電位，改善供電品質的特性，特別適宜計算機中心、航空航天監控中心，智能大樓等精密電子裝置場所。

Scope ofapplication

It is used for power transmission on power lines of rated voltage0.6/1kV or lower.lt has strong resistant characters againstelectromagnetic interference, thunder strike and even electricpotential, improving power sup- ply quality. It is especially suitableto place with precision electronic devices such as computercenter, space & aviation supervision center and intellectualbuildings etc.

二、執行標準

企業標準

Executive standard

Enterprise standard

三、型號名稱 Type and Description

注:

1、該產品可按用戶的使用要求，設計成具有阻燃性能或耐火性能的產品。訂貨時只需在原型號前加“ZR-”表示阻燃型，加“NH-”表示耐火型；

2、電纜的金屬屏蔽可按用戶要求有兩種形式:金屬絲編織或金屬帶繞包；

3、如需軟芯導體的電纜，應在原型號后加字母“R”。

Note: 

1: We also produce cable with fame resistant performance or fire resistant performance accordina to the reauirement of customerPrefix “ZR-”should be added to the original type for flame retardant cable and “NH-" added for fire-resistant cable.

2: There are two kinds of metallic shielding. One is metallic wire braiding shielding. The other is metallic tape wrapped shielding.

3: Prefix“R”should be added to the original type for ordering cable with soft conductor;

四、規格 Specification

五、使用條件

1、導體**長期允許工作溫度: 聚氯乙烯絕緣為70℃:交聯聚乙烯絕緣為90℃。

2、電纜短路時(最長持續時間不超過5S)，導體的**溫度不超過:聚氯乙烯絕緣為160℃;交聯聚乙烯絕緣為 250℃；

3、敷設時環境溫度應不低于0℃。

4、電纜允許彎曲半徑為:鎧裝電纜不小于電纜外徑的20倍:非鎧裝電纜不小于電纜外徑的15倍: 軟芯導體電纜不小于電纜外徑的10倍。

Working Condition

1: Max long-term working temperature allowed by conductor is70℃ for cable with PVC insulation, 90℃ for cable with XLPE insulation

2: Max temperature of conductor is no higher than160℃ for cablewith PVC insulation, 250℃ for cable with XLPE insulation duringshort circuit (The longest lasting time is no more than 5s).

3: Environment temperature for installation is not lower than 0℃

4: Bending radius allowed by cable is no less than 20 times that ofcable outer diameter for armored cable, 15 times that for inarmoredcable, 10times that for cable with soft conductor

六、電纜近似外徑

VVP型、VLVP型電纜外徑分別在VV型、VLV型電纜外徑的基礎上增加1~1.5mm2

YJVP型、YJLVP型電纜外徑分別在YJV型YJLV型電纜外徑的基礎上增加1~1.5mm2

VV22P型、VLV22P型電纜外徑分別在VV22型VLV22型電纜外徑的基礎上增加1.5mm2

YJV22P型YJLV22P型電纜外徑分別在YJV22型YJLV22型電纜外徑的基礎上增加1.5mm2

Approximate Outer Diameter of Cable

Outer diameter value of VVP type and VLVP type cable shouldbe added by 1~1.5mm2 on the basis of that of VV type and VLV typecable.

Outer diameter value of YJVP type and YJLVP type cable shouldbe added by 1~1.5mm2on the basis of that of YJV type and YJLVtype cable.

Outer diameter value of VV22P type and VLV22P type cableshould be added by1.5mm2 on the basis of that of VV22 type andVLV22 type cable.

Outer diameter value of YJV22P type and YJLV22P type cableshould be added by 1.5mm2on the basis of that of YJV22 typeａnd YJLV22 type cable.

七、主要技術參數

1、20C時導體直流電阻

參見0.6/1kV聚氯乙烯絕緣及護套電力電纜

2、絕緣電阻

Main Technical Parameter

1: DC resistance of conductor at 20C

2:Insulated resistance

3、交流電壓試驗成品電纜經受交流50Hz、5min、3.5kV的電壓試驗絕緣應無擊穿。

4、耐火型電纜的耐火特性應符合IEC60331或GB12666.6中的A類或B類耐火試驗要求。

5、阻燃型電纜的阻燃性能應符合IEC60332或GB/T18380.3標準中規定的A、B或C三類中任一類別阻燃性能要求。

3: Finished cable should endure A.C voltage test of 3.5kV, AC50Hz for 5min without puncture.

4: Fire resistant performance of fire resistance cable should meettesting requirement of category A or B stipu- lated in IEC60331or GB12666.6 standard.

5: Flame retardant performance of Flame retardant cable shouldmeet testing requirement of category A or B or C stipulated inIEC60332 or GB/T18380.3standard.