基本參數
| 測試項目 | 絕緣電阻（直流電壓施加方式） |
|---|---|
測試電壓/測量量程 | 25 V ≦ V < 100 V (2.000/20.00/200.0 MΩ), 100 V ≦ V < 500 V (2.000/20.00/200.0/2000 MΩ), 500 V ≦ V ≦ 1000 V (2.000/20.00/200.0/4000/9990 MΩ) |
| 基本精度 | ±2 % rdg. ±5 dgt. 25 V ≦ V < 100 V [0～20 MΩ], 100 V ≦ V < 500 V [0～20 MΩ], 500 V ≦ V ≦ 1000 V [0～200 MΩ] |
| 測試速度 | FAST：30ms/次，SLOW：500ms/次（切換） |
| 顯示屏 | LCD (壽命100,000小時),背光燈4階段 |
| 存儲功能 | 保存內容：額定測量電壓、比較器上下限值、測試模式、判定時蜂鳴音、測試時間、響應時間、電阻量程、測量速度 |
| 測試模式 | 連續模式、PASS STOP模式、FAIL STOP模式、強制結束時判定模式（切換） |
| 比較設置 | UPPER_FAIL：測量值≧上限值 PASS： 上限值＞測量值＞下限值 LOWER_FAIL：測量值≦下限值 |
| 判定處理 | 蜂鳴音、PASS/U.FAIL/L.FAIL 的LED 燈亮，UL_FAIL時U.FAIL/L.FAIL同時燈亮，EXT. I/O 輸出、通過RS-232C獲取判定結果 |
| 試驗時間計時器 | 0.045 s ～ 999.999 s（0.001 s 分辨率），從施加電壓到判定合格與否的時間 |
| 響應時間計時器 | 試驗開始后，禁止按照0.005 s ～ 999.999 s（0.001 s 分辨率）設置比較器判定動作的時間 |
| 模擬輸出 | DC +4 V f.s. |
| 接口 | RS-232C（標配），外部I/O（外部控制器用輸入，判定結果輸出），BCD輸出（ST5520-01） |
| 電源 | AC100 V ～ 240 V，50/60Hz，25VA |
| 體積及重量 | 215W×80H×166Dmm，1.1kg |
| 附件 | 使用說明書×1、電源線×1、EXT.I/O連接器×1、連接器蓋×1 |
Basic parameters
Test Items: Insulation Resistance (DC Voltage Application Mode)
Test Voltage/Measurement Range
(Manual/automatic)
25 V < V < 100 V (2.000/20.00/200.0 M_),
100 V < V < 500 V (2.000/20.00/200.0/2000 M_),
500 V < V < 1000 V (2.000/20.00/200.0/4000/9990 M_)
The basic accuracy is (+2%) rdg. (+5 dgt).
25 V < V < 100 V [0-20 M_],
100 V < V < 500 V [0-20 M_],
500 V < V < 1000 V [0-200 M_]
Test speed FAST:30ms/time, SLOW:500ms/time (switching)
LCD (life 100,000 hours), backlight stage 4
Storage function
Preserved contents: rated measurement voltage, upper and lower limits of comparator, test mode, buzzing sound when judging, test time, response time, resistance range, measurement speed
Storage: up to 10 groups (saveable/readable)
Test mode: Continuous mode, PASS STOP mode, FAIL STOP mode, Forced End Decision mode (Switching)
Comparison Settings UPPER_FAIL: Measured Value (> Upper Limit Value)
PASS: upper limit value > measurement value > lower limit value
LOWER_FAIL: Measured value < Lower Limit
Decision processing: buzzing, PASS/U.FAIL/L.FAIL L ED lights on, UL_FAIL U.FAIL/L.FAIL lights on at the same time, EXT.I/O output, RS-232C to obtain the decision results.
The test time timer ranges from 0.045 s to 999.999 s (resolution 0.001 s), the time from applying voltage to determining eligibility
After the start of the response time timer test, it is forbidden to set a comparator to determine the action time from 0.005 s to 999.999 s (0.001 s resolution).
Analog output DC+4V F.S.
Interface RS-232C (Standard), External I/O (External Controller Input, Decision Output), BCD Output (ST5520-01 only)
Power supply AC100 V-240V, 50/60Hz, maximum 25VA
Volume and weight 215W *80H *166Dmm, 1.1kg
Accessories: Instructions for Use *1, Power Wire *1, EXT.I/O Connector *1, Connector Cover *1
