砌墻磚成型試模是檢測儀器，用于工業與民用建筑砌墻磚抗壓強度試驗試樣制備，使用前務必仔細閱讀說明書。并由實驗人員操作，以避免操作不當引起的傷害。如需了解更多資料請與我公司客服人員聯系。
The wall brick forming test mold is a testing instrument for the preparation of compressive strength test samples of industrial and civil building wall bricks. Please read the instructions carefully before use. It is operated by experimental personnel to avoid injury caused by improper operation. For more information, please contact our customer service staff.
砌墻磚成型試模符合GB/T 2542-2012《砌墻磚試驗方法》和GB/T 25044-2012《砌墻磚抗壓強度試樣制備設備通用要求》標準中抗壓強度試驗方法要求，分一次成型模具和二次成型模具兩種。
The test mold for forming brick wall bricks complies with the requirements of compressive strength test methods in the standards of GB / T 2542-2012 "Test methods for brick wall bricks" and GB / T 25044-2012 "General requirements for equipment for preparing compressive strength samples for brick wall bricks". There are two types of primary mold and secondary mold.
砌墻磚成型試模尺寸：
1、一次成型試模組裝后型腔尺寸為：長120mm±15mm（可調節）； 寬120mm±10mm（可調節）；高115mm±5mm
2、二次成型試模組裝后型腔尺寸為：長240mm±15mm（可調節）； 寬120mm±10mm（可調節）； 高65mm±5mm
Brick wall mold test mold size:
1. The size of the cavity after the one-shot test mold assembly is: 120mm ± 15mm (adjustable); 120mm ± 10mm (adjustable); 115mm ± 5mm
2. The size of the cavity after the secondary molding test mold assembly is: 240mm ± 15mm (adjustable); 120mm ± 10mm (adjustable); 65mm ± 5mm
砌墻磚成型試模使用方法：
1、一次成型試模組裝后，用潤滑油進行抹刷，然后把磚試樣放入試模中，在中間和兩邊插入插板以確定厚度，前后方向用膠皮密封，初步擰緊螺絲固定試樣，取出插板，A終擰緊螺絲。把固定好樣品的試模放到振動臺上加入專用凈漿制樣。
2、二次成型試模組裝后，用潤滑油進行抹刷，放入專用凈漿材料，然后把磚試樣放入試模中的頂絲上，頂絲保證凈漿厚度不超過3mm，用螺絲把試樣固定，放到振動臺上進行振動，待凈漿材料硬化后拆模重新對另一面進行加工。
How to use the wall mold forming test mold:
1. After the molding test mold is assembled once, wipe it with lubricating oil, then put the brick sample into the test mold, insert the insert plate in the middle and both sides to determine the thickness, seal it with rubber in the front and back direction, and tighten the screw to fix the test In the same way, remove the plug-in board, and finally tighten the screws. Put the fixed mold on the shaking table and add special pure slurry to prepare the sample.
2. After the secondary molding test mold is assembled, wipe it with lubricating oil, put in special cleansing material, and then put the brick sample on the top wire in the test mold. The top wire ensures that the thickness of the clean pulp does not exceed 3mm. Fix the sample with screws, place it on a shaking table, and shake it. After the paste material is hardened, remove the mold and process the other side again.
砌墻磚成型試模保養：
試模使用結束后，把試模表面用鏟刀清理干凈，然后用潤滑油進行涂涮，以方便下次使用。
Maintenance of molding test molds for masonry bricks:
After using the test mold, clean the surface of the test mold with a spatula, and then coat it with lubricating oil to facilitate the next use.
