一、石膏板材抗折機產品簡介：
適用于石膏板材抗折強度試驗，試驗機外觀精美、工藝細膩，采用伺服控制系統，可實現勻速加載效率高穩定性好。采用觸摸屏控制，友好的人機操作界面。儀器內部設有行程限位和正負力值過載保護功能。具有測試速度可調、負荷測量精度高、操作方便等特點。適用于工廠、建筑工程質量檢測站、建筑公司、產品質量檢驗所、科研院校、道路橋梁現場等，生產檢驗、開發研究等領域。
Product introduction:
It is suitable for the flexural strength test of gypsum board. The testing machine has exquisite appearance and exquisite workmanship. It adopts servo control system to achieve uniform loading efficiency and high stability. Touch screen control, friendly man-machine operation interface. The instrument is equipped with internal travel limit and positive and negative force value overload protection functions. It has the characteristics of adjustable test speed, high load measurement accuracy, and convenient operation. Suitable for factories, construction engineering quality inspection stations, construction companies, product quality inspection institutes, scientific research institutions, roads and bridges, etc production inspection, development and research fields.
二、石膏板材抗折機技術參數：
?大試驗力：2KN
?有效檢測范圍：A大實驗力的1%-A
?負荷分辨率：0.1N
?負荷測量精度：示值的±1%以內
?試驗速度：4.2N/S/4.9N/S可調
?試驗空間范圍：150mm
?試件范圍：600×600mm
?驅動方式：伺服電機驅動
?電源：單相交流220V / 50Hz，電機功率550 W
?外形尺寸：700×800×1200mm
?重量:150KG
Technical parameters:
? A large test force: 20KN
? Effective detection range: 1% of A large experimental force-A
? Load resolution: 0.1N
? Load measurement accuracy: within ± 1% of the displayed value
? Test speed: 4.2N / S / 4.9N / S adjustable
? Test space range: 150mm
? Test piece range: 600 × 600mm
? Drive mode: servo motor drive
? Power supply: single-phase AC 220V / 50Hz, motor power 550 W
? Dimensions: 700 × 800 × 1200mm
Weight: 150KG
三、石膏板材抗折機產品特點：
?嵌入式Windows操作系統環境的測控軟件，實時顯示測試數據、曲線、試驗過程自動控制，試驗結束自動求取試驗結果，軟件簡便易用；
? 采用電腦控制，可實現力速度、位移速度、編程三種加載方式，可滿足不同標準試驗要求。
?采用伺服控制系統，精確控制檢測過程。
?采用觸摸屏控制，便于人機對話。
?試驗機內部設有行程限位和正負力值過載保護功能，防止誤操作引起試驗機的損壞。
Product features:
? Embedded Windows operating environment measurement and control software, real-time display of test data, curves, automatic control of the test process, test results are automatically obtained after the test, the software is simple and easy to use;
? Computer control can be used to achieve three loading methods: force speed, displacement speed, and programming, which can meet different standard test requirements. Zh
? The servo control system is adopted to precisely control the detection process. Zh
? Touch screen control for easy man-machine dialogue.
? The test machine is equipped with travel limit and positive and negative force value overload protection functions to prevent damage to the test machine caused by misoperation.
四、使用方法：
?首先將試驗機作水平調整，乃利用水平儀置于本機之機臺座上，而依水平儀指示調整基礎螺絲使呈水平(安裝機臺或移動機臺時調整)。
?啟動電源總開關，使電源通過本機各控制面板。
?根據試樣塊的測試要求，調節好兩支撐棍的跨距和支撐棍上定位塊的位置，保證試樣塊處在中間，調節壓輥上的配重塊，使壓輥保持水平。
?在試驗前，調整上、下行程設定環至所需之范圍上下限位置，使下夾具至此位范圍后會觸動極限開關而停機。
?選適當?shù)臏y試速度，無段速控制則轉動控制盤上之速度旋鈕到已測定出之速度指示數字即可。
?顯示器開機，并將所有顯示字幕歸零，準備接受測試。
?啟動馬達使中聯板下降開始測試，此時開始顯示出試件拉力數值，直到試件斷裂時，荷重保持zui大值, 記錄數值后，取下斷裂試件，再依上述方法夾持試件及顯示器數值，歸零后即可再測試，若測試已完成，請關掉電源
Fourth, use method:
? First adjust the level of the testing machine by using the spirit level on the machine base of the machine, and adjust the basic screws to be level according to the instructions of the spirit level (adjust when installing the machine or moving the machine).
? Turn on the main power switch to make the power pass through the control panels of the machine.
? According to the test requirements of the sample block, adjust the span of the two support sticks and the position of the positioning block on the support stick to ensure that the sample block is in the middle. Adjust the weight block on the pressure roller to keep the pressure roller horizontal.
? Before the test, adjust the upper and lower stroke setting rings to the required upper and lower limit positions, so that the lower clamp will trigger the limit switch and stop after the lower clamp reaches this range.
? Select the appropriate test speed. If there is no step speed control, turn the speed knob on the control panel to the measured speed indication number.
? Turn on the monitor and reset all displayed subtitles to zero, ready to be tested.
? Start the motor to start the test of the Vanda lowering. At this time, the value of the tensile force of the test piece is displayed. Until the test piece breaks, the load remains at a high value. After recording the value, remove the fractured test piece, and then clamp the test according to the method The value of the device and the display can be tested after returning to zero. If the test is completed, please turn off the power
