一、產品簡介：
纖維吸油率測定儀是 檢測儀器，用于公路工程瀝青路面用纖維作吸油率指標測定之用。
Product introduction:
Fiber oil absorption rate tester is a testing instrument for measuring the oil absorption index of fibers used in highway engineering asphalt pavement.
二、技術參數：
★振動時間：0-60min
★電源：220v50HZ
★試樣篩規格：0.5mm孔徑/直徑100MM
★振動速度：240次/分鐘
★振動振幅32mm
★振動時間：可人為控制
★外形尺寸：55X28X50mm
★ 重量：10kg
Technical parameters:
★ Vibration time: 0-60min
★ Power supply: 220v50HZ
★ Specification of sample sieve: 0.5mm aperture / diameter 100MM
★ Vibration speed: 240 times / minute
★ Vibration amplitude 32mm
★ Vibration time: can be controlled manually
★ Dimensions: 55X28X50mm
★ Weight: 10kg
三、產品特點：
★振動速度均勻，攪拌充分。
★采用時間繼電器設置控制振動時間。
★度均勻，攪拌充分。
★可人工自行控制振動時間（通過開關機實現）
Third, product characteristics:
★ The vibration speed is uniform and the stirring is sufficient.
★ Use the time relay setting to control the vibration time.
★ The degree is uniform, and stir well.
★ The vibration time can be controlled manually (by switching on and off)
四、操作方法：
★基本模塊
1，包含定標、測量、查詢、設置四個模塊。
2，操作簡單，無需 人員來操作
3，參數設置——點擊按鈕儀器自動校正
4，測試結果自動保存在電腦中，可通過查詢功能導出至Excel表格中進行分析。
★操作步驟
裝樣——稱重——放樣——測量——出結果（單個樣品檢測5分鐘以內完成，多樣品統籌時，平均第個樣品2分鐘）
★數據分析
數據分析主要是分析檢測數據的準確性、穩定性、標準偏差等檢測數據，同時通過檢測 數據調整生產工藝流程，從而把上油率調整到狀態，節約資源。
Fourth, the operation method:
★ Basic Module
1. Contains four modules: calibration, measurement, query and setting.
2, simple operation, no need for personnel to operate
3, parameter setting-click the button to automatically calibrate the instrument
4. The test results are automatically saved in the computer and can be exported to an Excel table for analysis through the query function.
★ operation steps
Loading—weighing—staking out—measurement—outcome results (single sample detection completed within 5 minutes, when multiple samples are coordinated, the average first sample is 2 minutes)
★ Data analysis
Data analysis mainly analyzes the test data such as accuracy, stability, standard deviation, etc. At the same time, the test data is used to adjust the production process to adjust the oiling rate to a good state and save resources.
五、使用方法：
★根據實驗需要，稱取相應質量的纖維、礦物油混合物，倒入儀器上的試樣篩中。
★設定振動時間，插到220V、50Hz電源上，按下電源開關，使其處于“開”的位置。
★達到設定時間后，儀器自動停機并發出報警聲。
★關掉電源開關，取下試樣篩，稱取試樣篩和吸有礦物油的纖維的質量，按有關公式計算的吸油率指標。
★做二次試驗時，重復上述步驟即可。
Five, use method:
★ According to the needs of the experiment, weigh the corresponding fiber and mineral oil mixture and pour it into the sample sieve on the instrument.
★ Set the vibration time, plug it into a 220V, 50Hz power supply, and press the power switch to make it "on".
★ After reaching the set time, the instrument will automatically stop and issue an alarm sound.
★ Turn off the power switch, remove the sample sieve, weigh the mass of the sample sieve and the fiber that absorbs mineral oil, and calculate the oil absorption index according to the relevant formula.
★ Repeat the above steps for the second test.
