瑞典Friborg點火試驗器

式點火器模型4610
點火試驗是塑料材料耐火試驗的一種。加纏繞在測試樣品周圍，電線被DC電流加熱，直到它發光，看測試樣品是否點燃。請注意，大多數新標準要求使用交流電流。（見點火器模型4670和4680交流電流）
用于測試標準：
IEC 60950-1:1999條款A(yù)4

瑞典Friborg點火試驗器

點火試驗是塑料耐火試驗的一種。
材料.加纏繞在試樣和導線周圍。
用DC電流加熱直到它發光，看是否有測試樣品。
點燃。請注意，大多數新標準要求使用交流電。
電流。（見點火測試模型4670和4680時）
4610型點火測試儀是手動版本。它
包含直流電源，觀察，計時和計算
手工做的。
技術規范
•測試樣本來源于直流電源。
•測試樣本持有人
•數字和v-meters
•校準時電壓測量夾
•連接元件線的端子
•加熱絲80%鎳和20%鉻- 150米包括在內
可選的–柜
•柜0.5 m3

瑞典Friborg點火試驗器

根據要求
標準
•透明門-進入洞操作
不開門
·風扇從柜中排出氣體
測試
可選-卷繞裝置
•幫助把電線卷到測試上
用6.3mm瀝青樣品
•測試樣品的夾具
•導線張力的重量

瑞典Friborg點火試驗器

Hot Wire Ignition test is a type of resistance test to fire for plastic
materials. Heating wire is winded around the test sample and the wire
is heated up with a DC-current until it glows to see if the test sample
ignites. Please note that most new standards require the use of AC
current. (See Hot Wire Ignition Tester Model 4670 and 4680 for ACcurrent)

The Hot Wire Ignition Tester Model 4610 is a manual version. It
contains a DC-source, and observations, timing and calculations are
done manually.
Technical specification
• The test sample is sourced by DC power
• Holders for the test sample
• Digital A- and V-meters
• Clips for Voltage measurement at calibration
• Terminals to connect the element wire
• Heating wire 80% Nickel and 20% Chromium – 150 m included
Optional – Cabinet
• Cabinet 0,5 m3
 according to requirement of
standard
• Transparent door – access holes to operate
without opening the door
• Fan blow out gases from cabinet after
testing
Optional – Winding device
• Helps to wind up the wire onto the test
sample with 6,3 mm pitch
• Clamps for test sample
• Weight for wire tension